ScotchcalTM High Performance Protective Films For the Professional Applicator   Product Bulletin I-45 June 1997 Replaces PB 1-45 dated November, 1996 U.S. USE ONLY General Description 3MTM ScotchcalTM High Performance Protective Films are noted for their overall excellent performance. These rugged, non-yellowing urethane films protect against stone chips, bug damage abrasion and weathering while allowing a vehicle's color brilliance to show through and its design intent to be maintained. Approved by automotive OEMs, these durable films are flexible, conformable and easy to apply. PUL 0612 is available in rolls of varying widths and in model-specific die-cut kits. PUL 1212 is available in 1 inch wide rolls. Product Construction Expected Effective Performance Characteristics Performance statements are based upon representative experience from testing throughout the United States; however, actual performance will be determined by substrate selection and preparation, exposure conditions, and maintenance of the marking. When applied, or when processed and applied according to 3M recommended procedures, an effective performance life of approximately five years may be expected. Physical and Chemical Characteristics Values given are typical and are not for use as specifications. If a specification is desired, a custom specification will be prepared. Any requests for a specification should be submitted to your local 3M representative. Shelf Life It is recommended that temperatures of 13ºC - 32ºC (55ºF - 90ºF) and 44% - 55% relative humidity be maintained in the film storage location. Film should be used within one year of purchase. Performance Properties These values represent typical data when tested to major urethane specifications and should not be used for product approval.         Results     Performance Test and Condition PUL 0612 PUL 1212 Tensile   MPa (PSI)20 (.029) 24 (.035)   Elongation > or=400% > or=400%   Peel Adhesion     Initial state --- 20 min @ 23ºC (73ºF) N/m (lb/in) 700 (4.0) 700 (4.0) Room temperature --- 72 hrs @ 23ºC (73ºF) N/m (lb/in) 800 (4.6) 800 (4.6) Heat resistance --- 168 hrs @ 70ºC (158ºF) N/m (lb/in) 900 (5.2) 900 (5.2) Moisture resistance --- 168 hrs @ 35ºC (95ºF)    100% R.H. - 2 hrs @ 70ºC (158ºF) N/m (lb/in) 900 (5.2) 900 (5.2) Thermal cycle --- 158 hrs @ 80ºC (176ºF) 1000 (5.8) 1000 (5.8) Environmental Simulation     Acid resistance Pass Pass Fuel resistance Pass Pass Heat resistance --- 168 hrs @ 70ºC (158ºF) Pass Pass Moisture Resistance --- 168 hrs @ 35ºC (95ºF)    100% R.H. - 2 hrs @ 70ºC (158ºF) Pass Pass Thermal cycle --- 158 hrs @ 80ºC (176ºF) Pass Pass Solvent resistance Pass Pass Shrinkage < .1% < .1% Gravelometer (SAEJ-400) No ruptures No ruptures Outdoor Deck Weathering       Arizona 45º South Facing (unbacked)    - No objectionable gloss loss or change,      adhesion loss, film crackup, or crazing. 12 months 24 months 36 months Less than 10% gloss loss and no more than 2.5 De color change Less than 10% gloss loss and no more than 2.5 De color change Florida 5º South Facing (unbacked)    - No objectionable gloss loss or change,      adhesion loss, film crackup, or crazing. 12 months 24 months 36 months Less than 10% gloss loss and no more than 2.5 De color change Less than 10% gloss loss and no more than 2.5 De color change Product Characteristics Adhesive Acrylic PSA   Liner White --- Bleached paper with release coating   Max service temperature Film softens above 67ºC (150ºF) Application For detailed information on application of 3MTM ScotchcalTM High Performance Paint Protective Films, see instruction bulletin 2-14. For best results, apply the film to a clean substrate at temperatures between 13ºC - 32ºC (55ºF - 90ºF). Important Notice to the Publisher: All statements, technical information and recommendations herein are based on tests 3M believes to be reliable. 3M does not warrant or guarantee the accuracy or completeness of this information. UNLESS SPECIFICALLY STATED OTHERWISE, THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTEES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTEES OF MERCHANTABILITY AND FITNESS FOR PURPOSE: seller's and manufacturer's only obligation shall be to replace such quantity of the 3M product proved to be defective. Before using, user shall determine the suitability of the 3M product for its intended use, and user shall assume all risk and liability whatsoever in connection therewith. NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE, IN TORT, CONTRACT OR UNDER ANY OTHER LEGAL THEORY, FOR ANY LOSS OR DAMAGE, DIRECT, INCIDENTAL, OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS OR REVENUES) ARISING OUT OF THE USE OF OR THE INABILITY TO USE OR IN ANY OTHER WAY RELATED TO THE PRODUCT. No statement or recommendation not contained herein shall have any force or effect unless contained in an agreement signed by officers of seller or manufacturer. Automotive Division 3M Center, Building 223-1S-02 St. Paul, MN 55144-1000